See us at the PMCA Show in Lancaster, PA on 4/15
Home » Mill » Hammer » Page 5
Hammer mills use rotating hammer or knives to break-up wet or dry product that has been fed into the chamber of the machine. The rotating hammers or knives in the chamber of a hammer mill reduce the side of the product by impacting the product and by forcing the product to impact the interior of the chamber. The hammers within the chamber of a hammer are sized so that the end of the hammer almost impacts the interior wall of the chamber. A hammer mill has a screen to form the bottom of the chamber. Once the product has been reduced to the proper size, the product falls through the screen below the chamber. The screen can be changed to allow.
Hammer mills can be designed with different numbers of hammers or blades. The proper number of hammers or blades for an application is based the product that is to be processed, the size reduction necessary from the hammer mill, the volume that the hammer mill must process, and other specifications of the application. The hammers in a hammer mill can also have different features. The hammers can have knife edges, blunt (impact) edges, or a knife edge and a blunt edge. The type of hammer needed for the application is based on the type of product that is to be processed by the hammer mill. Hammer mills can also have fixed or swinging hammers or blades.
Fitzmill Model DAS06, 316 stainless steel, particle reduction, hammer mill with pounds of product per hour – depending on materials and application. Equipped with 12" long x 12" wide x 10" deep product hopper with safety grid, 4" OD x 18" long single auger feed screw powered by ¼ Hp motor drive with variable speed gearbox, (16) fixed, reversible stainless steel knife / impact blades driven by 10 Hp motor drive and has 15" long x 6" wide product discharge port with safety grid and 36" floor clearence. Control panel has mill and feed screw start, stop push buttons. Mounted on (4) leg stainless steel frame with locking casters. Used for precision grinding and controlled particle size reduction in pharmaceutical processing and other sanitary industries.
OAD: 53"L x 42"W x 66"H
Fluid Air, Model 007 Granumill, all stainless steel pilot size product reduction system. Capable of handling both wet or dry products with thru puts from 2 to 2250 lbs per hour, has screen width of 7" and capable of handling 10 to 400 size mesh with finished reduction particle sizes from 2000 to 27 microns all with proper change parts and depending on materials and application. Maximum speeds of 5,000 rpm’s and maximum tip speed of 21,000 feet per minute. Equipped with 18" long x 15" wide x 15" deep stainless steel product hopper with 3" OD x 28" long product feed screw and secondary pan feeder to reduction chamber with bolt down cover and (4) fixed rotary impact blades with flat square and rounded blades for impacting hard materials and fine grinding also breaking up soft or wet materials. Control panel has frequency and fault controls with mill and feeder readouts for rpm and percent of load controllers. Mounted on stainless steel base frame with casters.
OAD: 48" L x 32" W x 78" H
Fitzmill Model DAS06, 316 stainless steel, sanitary, with enclosed, pressurized chamber, particle reduction, hammer mill with pounds of product per hour – depending on materials and application. Equipped with 15" long x 15" wide x 12" deep product hopper with safety grid and 4" OD x 12" long single auger feed screw powered by 3 Hp motor drive, 6" x 11" feed throat with (16) fixed, reversible stainless steel, blunt / knife blades driven by 10 Hp motor drive and has a 14" long x 7" wide product discharge port with safety grid and 30" floor clearence. Control panel has mill and feed screw start, stop push buttons with feed screw speed control dial, amp guage and e-stop, enclosed pressure control regulator with power on / off, safe pressure and alarm indicator with high, low and safe pressure guage. Mounted on (4) leg stainless steel frame with locking casters. Used for precision grinding and controlled particle size reduction in pharmaceutical processing and other sanitary industries.
OAD: 69" L x 50" W x 55" H
Quadro Model 194S, 316 stainless steel particle size reduction Comil. Rated from 1,800 to 4,000 lbs of product per hour – depending on materials and application. Equipped with 5¾" diameter feed throat, 8" diameter screen and 6" diameter discharge port with 21" ground clearance. Control panel with push button start / stop. Mounted on stainless steel (4) leg frame with casters.
OAD: 40"L x 32"W x 50"H
Mikron, Mikro Pulverizer, Model SCB, Stainless steel hammer mill with amount of product per hour – depending on materials and application. Equipped with 16" wide x 16" long x 12" deep product feed hopper, (2) 3" OD feed augers and (12) sets of 6" wide swinging blunt impact hammers powered by 10 Hp motor drive and has product discharge with 56” floor clearance. Mounted on (4) leg mild steel base frame. Used to grind, de-lump, pulverize and process wet / dry products.
OAD: 50" L x 42" W x 78" H
Rietz Model RA3-12-K122, versatile, variable speed 45 degree angle disintegrator with pounds of product per hour – depending on materials and application. Equipped with 24" OD reduction chamber and has (5) sets of 3 impellers 12" OD stacked on top of each othe rwith 24" OD cover and 360 degree reduction screen (change part per application) which is held between the housing cradle and has clamp down access door with attached product funnel and 4" OD product port. Belt driven rear mounted 50 Hp motor drive with safety guarding and e-stop. 18" OD x 18" funnel style discharge with 4" floor clearence (with funnel) and 43" discharge height (without funnel). Mounted on heavy duty (4) leg frame with leveling screws.Used for high-speed shredding and wet grinding of fibrous and other tough materials, also used for fine pulping dispersing and homogenizing.
OAD: 94" L x 50" W x 70" H
Rietz Model RA3-12-K122, versatile, variable speed 45 degree angle disintegrator with pounds of product per hour – depending on materials and application. Equipped with 24" OD reduction chamber and has (5) sets of 3 impellers 12" OD stacked on top of each othe rwith 24" OD cover and 360 degree reduction screen (change part per application) which is held between the housing cradle and has clamp down access door with attached product funnel and 4" OD product port. Belt driven rear mounted 75 Hp motor drive with safety guarding and e-stop. 18" OD x 18" funnel style discharge with 4" floor clearence (with funnel) and 43" discharge height (without funnel). Mounted on heavy duty (4) leg frame with leveling screws.Used for high-speed shredding and wet grinding of fibrous and other tough materials, also used for fine pulping dispersing and homogenizing.
Fitzmill, Model DKAS012, stainless steel, hammer mill with pounds of product per hour – depending on materials and application. Stainless steel contact parts. Equipped with 22" long x 16" wide x 5" deep feed pan and 12" x 12" feed throat with (32) fixed impact blades and 14" x 16" discharge port with safety grid and 42" ground clearance Control panel has start, stop, e-stop push button controls and 20 Hp motor drive. Mounted on (4) leg frame with casters.
OAD: 48" L x 38" W x 68" H
Fitzmill, Model DASO6, stainless steel hammer mill with production rates per hour – depending on materials, application and machine configuration. Equipped with 24" long x 16" wide x 4" deep feed pan and 6" x 6" feed throat with (16) fixed knife / impact blades powered by 7.5 Hp motor drive. 15” long x 6” wide product discharge with 32” floor clearance. Control panel has start, stop, reset push button controls. Mounted on (4) leg stainless steel frame.
OAD: 60" L x 36" W x 60" H Without Casters 68" H With Casters
Fitzmill, Model DKAS012, stainless steel hammer mill with pounds of product per hour – depending on materials, application and machine configuration. Equipped with 5-3/4" OD product port and 12" x 12" feed throat with (32) fixed knife / Impact blades powered by 20 Hp motor drive, bottom 10" ID product discharge port with 24” floor clearance. Control panel has start, stop push buttons and hand held controller. Mounted on (4) leg stainless steel legs with casters. Used to grind, de-lump, pulverize and process wet or dry products.
OAD: 60" L x 60" W x 78" H With Casters 58" H Without Casters
Variable speed, auger feed, S/S hammer mill with 30" x 40" hopper. Equipped with 4" diameter in feed auger with safety grate. Type 225 fixed blade assumption with knife on one side and impact on the other. Unit sits on S/S base.O.A.D:53"h x 65"L x 49"w
Fitzmill Model DAS06, 316 stainless steel, pan fed reduction hammer mill with pounds of product per hour – depending on materials and application. Equipped with 26" long x 20" wide stainless steel feed pan, with 6" feed throat and (16) fixed stainless steel reversible blunt / blunt blades, 12" long x 5" wide product discharge with safety grid and 38" floor clearence. Control panel has reset, start and stop push button controls. Mounted on (4) leg stainless steel frame with locking casters. Used for precision grinding and controlled particle size reduction in pharmaceutical processing and other sanitary industries.
OAD: 56" L x 34" W x 66" H
Sign up for our newsletter to receive the latest in packaging tips, case studies and more.