Used Cartridge Equipment
46 Filler Paste machines IN-STOCK!

More Photos: 2

Automatic two head piston filler rated up to 40 containers per minute - depending on materials and application. Equipped with 23" diameter 22" deep stainless steel product hopper, two 4" ID (64 oz) pistons, two 1/2" fill nozzles set on 5" centers, and dual 80" long lugged chain feed conveyors set on 5" centers.

OAD: 80" L x 45" W x 76" H

More Photos: 2
Play Video

Twin piston filler, rated up to 30 strokes per minute - depending on materials and application. Equipped with 28" diameter 34" deep product hopper and cover, twin 4" ID (45oz) pistons and two nozzles fittings set on 7" centers. Mounted on locking casters.

OAD: 60" L x 36" W x 73" H

More Photos: 4

Twin piston filler, rated up to 30 strokes per minute - depending on materials and application. Fill range; fractional oz up to 45oz with proper change parts. Accuracies: 1/2% of volume filled. Equipped with 60" long x 40" wide x 34" deep roll over the filler product hopper, currently set with twin 1-7/8 ID pistons with maximum fill of 8.9oz,and 1/2" OD nozzles set on 7" on centers. PLC controller with swing arm control panel mounted on four leg base frame.

OAD: 78" L x 48" W x 85" H

More Photos: 2
Play Video

Four head piston filler rated up to 30 strokes per minute - depending on materials and application. Equipped with 36" long x 20" wide x 12" deep product hopper with cover and level detector, dual twin 2" ID pistons with fill up to 17.8oz and 1" ID nozzles on a 31" long slide bar. Mounted on adjustable height frame with locking casters.

OAD: 48" L x 48" W x 79" H

More Photos: 2
Play Video

Semi-automatic, S/S inline, single head piston filler speeds dependent on product, size fill, and operator dexterity. Has 20" ID x 20" Deep S/S cone style product hopper, with a 16 oz 8 3/4" L x 2 3/4" ID S/S, single piston with a 5/8" OD and 1/8" ID product nozzle with 40" floor clearance, with motor drive and variable speed controller, and is mounted on height adjustable base frame.

OAD: 41" L x 26" W x 65" H

More Photos: 2

Slurry transfer pump aned filler rated up to 30 cycles @ min, depending on application. Fully automatic with a manual on / off valve, USDA and FDA corrosion resistant polypropylene construction has 3" inlet / outlets and can be used for a variety of products such as sauces, pie fillings, pate, jelly, yogurt, mustard, ketchup, vinegar and more, based on water and air inlet pressure of 2.11 kgf/cm2-30psi you have minimum / maximum filling capacities of 226.5 - 4536.0 cc, 226.5 - 4536.0 grams, 8.0 - 154.0oz, and 13.8 - 276.8 cu in per cycle.

OAD: 64" L x 26" W x 43" H

More Photos: 2

Inline, 6 hd piston filler capable of speeds from 60 -150 cpm depending on application. Fill range of: 3/4oz - 32oz, per nozzle (with proper change parts) currently set with (6) 2" OD x 9" L S/S, pistons to 16oz fills, can handle jars, bottles, and cans, fills from liquids to pastes. Has a 19" L x 36" W x 19" D, S/S conical product hopper, 6 lane 72" L lugged walking beam main product conveyor set on 6" centers with bottom up fill, no container / no fill, start / stop and e-stop, controls and mounted on cast iron heavy duty base frame.

OAD: 72" L x 58" W x 83" H

More Photos: 3

Inline, 4 head piston filler rated up to 15 cycles per minute - depending on materials and application. Fill range: up to 32oz. Equipped with 3-1/4" conveyor, worm screw product indexing, bottom up fill, no container / no fill. All stainless steel contact parts. Change parts required to accommodate range. Currently set with four 22 oz pistons.

OAD: 108" L x 55" W x 72" H

More Photos: 2

Semi-auto, single head piston filler rated up to 20 strokes @ minute, depending on product and material. All 304 S/S contact parts, fitted with 12 oz piston and can handle both hot / cold product with proper change parts, has a 24" ID x 10" straight wall, and 12" slant, S/S, product hopper with a 12 oz 2" ID x 7 1/2" L single piston, with a 2" OD nozzle, and is mounted on a stand with casters.

OAD: 48" L x 24" W x 66" H

More Photos: 2

Semi-auto, single head piston filler rated up to 20 strokes @ minute, depending on product and size fill. All 304 S/S contact parts, fill range from fraction of an oz to 32 oz and can handle both hot / cold product with proper change parts, has a 22" ID x 14" Deep S/S, product hopper with a 3-3/4" ID x 8" L single piston, and is mounted 34" L x 18" W, H style stand with casters for mobility.

OAD: 48" L x 24" W x 62" H

More Photos: 3
Play Video

Stainless steel, semi-automatic piston filler. Equipped with 26" diameter x 22" deep hopper, 2-7/8" diameter sanitary piston with an adjustable fill range 4 to 20 oz. and 22mm nozzle. Mounted on casters.

OAD:36"L x 32"W x 66"H

More Photos: 2

10 Hd, S/S Piston Filler, Was with the Werkerle tube filling machine out of DPT

More Photos: 2

10 Hd, S/S Piston Filler Was with the Werkerle tube filling machine out of DPT

More Photos: 2

Twin piston, S/S, filler capable of speeds up to 60 cpm (depending on application), min/max fill rane of 3 oz - 16 oz, with an accuracy of +/- 0.1%. Unit has a 4 ft³ (30 gal) S/S bulk product hopper, (2) 3" ID x 4"L pistons, and a height adjustable column with hydraulic jack assist for a 41"H - 46"H discharge. Mounted on a common base frame with (4) legs and casters.

OAD: 80"L x 48"W x 72"H

More Photos: 2

Automatic, stainless steel, 8-head piston filler rated up to 72 cycles per minute - depending on materials and application. Filling capacities: 0.1oz to 62 oz with proper change parts. Equipped with 52" L x 22" W x 22" D jacketed product hopper with single sweep blade paddle agitator and flip top cover with shut-off switch, 3" dia x 14" L, angled air assist pistons with PLC and panel display.

OAD: 138" L x 60" W x 76" H

More Photos: 1

Raque Traveler

More Photos: 2

Twin S/S piston filler with 7 cuft hopper. Equipped with two 12 oz (7" long x 2-1/2" diameter) pistons with 1-1/2" diameter diving nozzles. Mounted on casters.


OAD: 48"L x 40"W x 74"H

More Photos: 3

Twin piston, S/S, filler capable of speeds up to 60 cpm (depending on application), min/max fill range of 3 oz - 16 oz, with an accuracy of +/- 0.1%. Unit has an 8 ft³, S/S, slanting bulk product hopper measuring 38"L x 26"W x 36"D, (2) 3" ID x 4"L pistons, and a height adjustable column with hydraulic jack assist for a 41"H - 46"H discharge. Mounted on a common base frame with (4) legs and casters.

OAD: 48" L x 44" W x 74" H

More Photos: 2

Semi-automatic, two head, paste filler. Container size range: 7/16" - 2- 3/16" in Diameter; 2" - 10" in Height. Equipped with twenty-two position rotary disc, 2 cu.ft. stainless steel jacketed hopper with level sensor, two 8 oz pistons and dual plug tamp station. Stainless steel contact parts.

OAD: 83"L x 47"W x 83"H

More Photos: 3

6 head inline piston filler capable of up to 120 cpm. Currently equipped with 32 oz. pistons. Unit has 30 gallon hopper w/ low product sensor, timing screw, 8'(L) x 4 1/2"(W) infeed conveyor w/ cam operated right angle transfer, walking beam type index system, bottom up fill, and Plexiglas guarding.

OAD: 117"(L) x 92"(W) x 68"(H)

More Photos: 1

Inline, 2 head piston filler, rated at speeds up to 20 containers per minute - depending on materials and application. Fill range of: 16 - 128 ounces. Equipped with two one gallon stainless steel pistons with 1" ID nozzles set on 8" centers, 29" L x 20" W x 21" D, S/S product hopper and 10' indexing conveyor.
OAD: 125" L x 74" W x 76" H

More Photos: 2

Geyer inline piston filler. Equipped with 114" long x 4" wide infeed conveyor with stainless steel tabletop belt and right angle transfer into filling area via walking beam and pin-type push bars, 40 gallon agitated product hopper, six 32oz pistons, 7/8" nozzles, bottom up fill, no container/no fill and a 86" long x 6" wide discharge conveyor with stainless steel belt.

OAD: 154" L x 78" W x 64" H

More Photos: 3

Automatic four head inline piston filler capable of speeds up to 80 CPM. Unit has a max container width of 4" and a max height of 12". Intermittent motion filler, has bottom up fill and is currently equipped w/ 1 1/4" diameter pistons for a fill range from .49 oz to 9.8 oz, on 4 1/2 centers. Can run up to 32oz fill w/correct change parts. Has 3/4" diameter fill nozzles, and has a 90" L indexing conveyor with four 4" W lanes. Has an all S/S product hopper 30" L x 23" W x 23" H hopper.

OAD: 92" (L) x 48" (W) x 72" (H)

More Photos: 2

S/S Single Piston filler rated to 20 cpm, currently equipped with 9oz piston for 1 - 9 oz fills. Filler will accept 16 oz and / or 32 oz pistons available as a change part. Features a 1/2" diameter nozzle, 9 gallon hopper, 6 1/2" lugged infeed on 5" center. Bottom-up fill with variable height adjuster. Mounted on casters.

OAD: 62'' L x 44'' W x 70'' H

More Photos: 3

Automatic, intermittent motion, inline 4 head "Hot Fill" piston filler capable of speeds up to 80 cpm depending on materials and application. Maximum container size: 4" in diameter 12" in height. Equipped with stainless steel full jacketed and agitated product hopper, bottom up fill currently set with (4) 1-1/4" ID pistons with fills up to 9.8 oz, with positive shutoff valves, set on 4-1/2" centers and can run up to 32oz fills with proper change parts and features 3/4" diameter fill nozzles, 90" Long indexing conveyor with four 4" Wide lanes and motor drive.

OAD: 102" L x 50" W x 94" H

More Photos: 2

Automatic twin piston filler capable of doing up to 40 cpm (depending on product & container size). Unit equipped with two 64 once pistons currently yoked together for 1 gallon fill. Equipped with a 9 gallon stainless steel hopper, 6' lugged chain conveyor set on 5-1/2" centers. Bottom-up fill. Last ran 5lb plastic tub of sour cream in a dairy operation.
(OAD: 98"L x 36"W x 76"H)

More Photos: 2

Automatic in-line twin piston filler. Equipped with a nine gallon agitated stainless steel product hopper, twin 16 oz. pistons with a fill range from 2oz. to 16 oz., 1/2" fill nozzles, bottom up fill and 6' long flited conveyor set on 5" centers. All stainless steel or food grade non metalic contact parts. Speed dependant on product and application.

OAD: 81" L x 30" W x 78"H

More Photos: 2

Automatic, intermittent motion 4 piston in-line filler, rated to 80 containers per minute, depending on product and fill. Currently set up with 4 oz pistons for 0.5 - 4 oz fills, on 1-3/4 centers, 1/4" fill nozzles. 18 gallon product hopper, with 1" valve ports. All stainless steel contact parts , 3 1/4"W x 87" L table top conveyor, pneumatic cylinder container handling & variable speed drive.
(OAD 54"L x 92"W x74"H)

Ten (10) head stainless steel paste filler with jacketed 10 gallon scrape agitated hopper. Machine currently set with (10) 1 3/8'' for 5 oz max fill pistons.(Up to a 10 oz max fill with proper pistons change parts from oem). Hopper capable of temperatures up to 200 deg. F. and is equipped with temperature gauge. Pistons are pneumatically actuated for fill deposit. Additional feature includes a self contained heating system that maintains a constant temperature throughout jacket, piston block and fill nozzles. Unit was last filling a heated cheese product while mounted over a Multivac Thermo former. Filler is mounted on an adjustable steel base with rolling locking casters. OAD: 51''(L) x 54''(W) x 72''(H)

Ten (10) head stainless steel paste filler /depositor with jacketed 10 gallon scrape agitated hopper. Machine currently set with (10) 1 3/8'' 5 oz max fill pistons.(Up to a 10 oz max fill with proper pistons change parts). Hopper capable of temperatures up to 200 deg. F. and is equipped with temperature gauge. Pistons are pneumatically actuated for fill deposit. Additional feature includes a self contained heating system that maintains a constant temperature throughout jacket, piston block and fill nozzles. Unit was last filling a heated cheese product while mounted over a Multivac Thermo former. Filler is mounted on an adjustable steel base with rolling locking casters. OAD: 51''(L) x 54''(W) x 72''(H)