Fitzpatrick Machines

Fitzpatrick Dryer Fluid Bed FA 150

• Manufacturer: Fitzpatrick
• Model Number: FA 150
• Frain Number: 5H9670

Fitzpatrick Model FA 150, 150 Kg, stainless steel fluid bed, batch dryer with maximum capacity of 150 Kg or 330.6 Ibs per batch or 8.6 cu ft total container volume with 1500 to 2000 cfm standard and up to 2500 cfm and volumes of product per hour – depending on materials and application. All 304 stainless steel construction with 2B finish exterior and # 4 finish interior and has 45" OD x 40-1/4" long stainless steel main chamber with 10Hp motor drive blower fan mounted above filtration and heating system with (4) 1/2" OD NPT side drains and bottom lower transition discharge section with 1" bottom drain and (2) product carts on casters. HEPA filter gauges with chart recorder has magnehelic and pressure gauges. Remote above mounted climate control air handling system with dehumitifier, pre-heater, humidifier, final heater and Farr 30/30 95% HEPA filters to fluid bed dryer. NEMA 7 enclosure mounted on dryer with start, stop buttons for fan and agitator, electrical wiring and equipment designed for hazardous locations class l & ll division 1. Mounted on stainless steel frame with leveling legs.

Drying is achieved in a FitzAire system as gas flows upward through the solids in the container. Gas is pulled through the bed, partially suspending the particles in the gas stream in a random, boiling motion. Drying occurs as moisture is transferred from the particles to the fluidizing gas.

OAD: 96" L x 60" W x 102" H

Fitzpatrick Mill Chilsonator 1.5L X 8D

• Manufacturer: Fitzpatrick
• Model Number: 1.5L X 8D
• Frain Number: 5H9600

Fitzpatrick, Model DM 1.5L X 8D, Chilsonator roller compactor mill, capable of processing from 35Kg to 135Kg (77 lbs to 297 lbs) of product per hour – depending on materials, application, environment and machine configuration. Stainless steel contact parts. Equipped with agitated, vertical screw feed product hopper with 1-1/2" OD product feed screw driven by variable speed motor drive, 1.5" L x 8" OD compaction rollers and hammer mill with (16) rotary knife blades for in air impact for harder compacts, and reduction screen (change part per application). Control cabinet has push button start, stop for main power, granulator, compactor, rollers, vertical and horizontal feed screws, with oil, air and amp gauges, panel purged and granulator on, start and stop push buttons. Mounted on stainless steel frame.

OAD: 54" L x 46" W x 72" H

Fitzpatrick Mill Hammer DAS06

• Manufacturer: Fitzpatrick
• Model Number: DAS06
• Frain Number: R34250

Fitzmill, Model DASO6, stainless steel hammer mill with production rates per hour – depending on materials, application and machine configuration. Equipped with 26" long x 20" wide x 4" deep feed pan, 6" wide x 4" high feed throat and (16) fixed knife / impact blades powered by 7½ Hp motor drive. Product discharge port is 15” long x 5¾” wide with 29” floor clearance. Mounted on (4) leg frame.

OAD: 41" L x 34" W x 64" H

Fitzpatrick Mill Hammer DAS06

• Manufacturer: Fitzpatrick
• Model Number: DAS06
• Frain Number: R34270

Fitzmill Model DAS06, 316 stainless steel, particle reduction, hammer mill with pounds of product per hour – depending on materials and application. Equipped with 12" long x 12" wide x 10" deep product hopper with safety grid, 4" OD x 18" long single auger feed screw powered by ¼ Hp motor drive with variable speed gearbox, (16) fixed, reversible stainless steel knife / impact blades driven by 10 Hp motor drive and has 15" long x 6" wide product discharge port with safety grid and 36" floor clearance. Mounted on stainless steel frame with locking casters.

OAD: 53"L x 42"W x 66"H

Fitzpatrick Mill Hammer DKAS012

• Manufacturer: Fitzpatrick
• Model Number: DKAS012
• Frain Number: R31742

Fitzmill, Model DKAS012, stainless steel hammer mill with pounds of product per hour – depending on materials, application and machine configuration. Equipped with 5-3/4" OD product port and 12" x 12" feed throat with (32) fixed knife / Impact blades powered by 20 Hp motor drive, bottom 10" ID product discharge port with 24” floor clearance. Control panel has start, stop push buttons and hand held controller. Mounted on (4) leg stainless steel legs with casters. Used to grind, de-lump, pulverize and process wet or dry products.

OAD: 60" L x 60" W x 78" H With Casters
58" H Without Casters

Fitzpatrick Mill Chilsonator IR520

• Manufacturer: Fitzpatrick
• Model Number: IR520
• Frain Number: R31157

Fitzpatrick Model IR520, 316 stainless steel, roller, Chilsonator (roller compactor / hammer mill). Rated up to 220 lbs. of product per hour – depending on materials, application, machine configuration and environment. Equipped with (2) screw feed design and has 13" long x 8" wide x 12" deep ID stainless steel product hopper with rotary product feeder, 3" OD horizontal screw that eliminates vacuum de-aeration to 2" vertical pre-compression screw that compresses product for more uniformity prior to feeding into the 2" x 8" grooved product compaction rollers with roller force of 26.3 KN/CM and roller gaps of 1mm to 6mm, powered by 5 Hp motor drive with onboard stainless steel Fitzmill Model M5A hammer mill with (16) fixed stainless steel blades and 6" OD product discharge with 49” floor clearance. Control panel has A/B PLC with PanelView. Mounted on (4) legs stainless steel frame.

OAD: 55" L x 48" W x 107" H Chilsonator
42" L x 28" W x 63" H Control Panel

Fitzpatrick Mill Chilsonator IR4LX10D

• Manufacturer: Fitzpatrick
• Model Number: IR4LX10D
• Frain Number: R31158

Fitzpatrick Model IR4L X 10D, 316 stainless steel, roller compactor chilsonator with onboard stainless steel Fitzmill Model D6A hammer mill rated up to 800 lbs of product per hour – depending on materials, application, machine configuration and environment being run in. Equipped with (2) screw feed design and has 19" long x 16" wide x 20" deep ID, stainless steel product hopper with 4" OD horizontal screw that eliminates vacuum dearation to 5" OD vertical pre-compression screw that compresses the product for more uniformity prior to feeding into the 4" x 10" groved product compaction rollers with roller force of 17.6 KN/CM and roller gaps of 1mm to 6mm, powered by 5 Hp motor drive with onboard stainless steel Fitzmill Model D6A hammer mill has (16) fixed stainless steel impact blades powered by 5 Hp motor drive with 14” long x 6” wide product discharge and 39” floor clearance. Remote control cabinet has A/B panelview touch pad controller with e-stop. Mounted on (4) legs stainless steel frame.

OAD: 108" L x 77" W x 120" H Chilsonator
36" L x 17" W x 72" H Control Panel

Fitzpatrick Mill Chilsonator 2LX8D

• Manufacturer: Fitzpatrick
• Model Number: 2LX8D
• Frain Number: R26451

Fitzpatrick, Model 2L X 8D, chilsonator roller compactor mill. Able to process 45Kg to 181Kg (100lbs to 400 lbs) per hour – depending on materials, application, environment and machine configuration. Equipped with 316 stainless steel contact parts, a 6" diameter charge port, 2½" OD / 1¾" ID tri-clamp style discharge with 8½" ground clearance , feed system controlled by both a vertical and horizontal screw and model JT homoloid mill. The vertical screw has 2" OD and is driven by ½ Hp motor with a speed range of 100 to 450 rpm. The horizontal screw has 3" OD and is driven by ¼ Hp motor with a speed range of 0 to 62 rpm. The compaction rolls are 2" wide x 8" OD and made of 17-4PH stainless steel. The homoloid mill equipped with (16) 2½" long x 1" wide knife blades powered by 1½ Hp motor drive. Mounted on 304 stainless steel base with locking casters

OAD: 75" L x 63" W x 88" H