Product
Lee, Model 250D9MS, 250 gallon capacity, 316 stainless steel, jacketed double motion kettle. Vessel dimensions: 52" diameter x 39" deep. Equipped with lift up covers, 3 Hp bridge mounted scrape agitator, flush mounted sensor and 3" Tri-Clamp style bottom discharge with ball valve and 18" ground clearance. Mounted on (3) leg frame.
Jacket Ports:
(2) 1½" NPT
Nat’l Brd: 12035
MAWP: 90 PSI @ 332°F
MDMT: -20°F @ 90 PSI
OAD: 70"L x 55"W x 80"H
Fanuc, 4 axes, servo driven, robotic case palletizing, automatic pallet stretch wrapper system, with number of cases per minute – depending on materials and application. Capable of moving product from floor level up to 123" in height, and has range of motion of 720 degrees, rated to maximum pick-up weight of 185 Kg. Equipped with vacuum pic-n-place head mounted on robotic arm with 123.72". maximum horizontal reach and has vacuum pump. Remote control panel has Fanuc R30iB controls with digital hour counter and auto / manual switch, fault, fault reset, power and e-stop push button controls, also has hand held, touch pad controller with display.
PMI, Model VXL2-15, automatic, inline, servo driven, case packer. Rated from 5 to 13 cases per minute with number of product – depending on materials, application and pack pattern. Case size range: 5" to 10" in Length x 4" to 7" in Width x 3" to 6" in Height. Equipped with product infeed conveying section, 64" long blank case magazine, fixed case pockets set on 7½" centers, hot melt glue system, bottom case sealer with bottom compression, 12" x 10" product accumulation table with sweeping arm loader, top case sealer and 8" wide x 58" long discharge conveyor. Control panel with AB PLC and touch screen HMI.
OAD: 180"L x 137"W x 94"H
Inline, rotary drop roll die former, hard candy forming machine with amount of product per hour – depending on materials and application. All stainless steel contact parts. Equipped with 6" OD x 10" wide adjustable gap pre-compression forming drums powered by a 1 Hp drive and 8" diameter x 10" wide (8¾" wide tooled) fixed jacketed forming dies powered by a 5.4 Hp drive with a variable speed gearbox. Mounted on a painted base frame.
OAD: 73"L x 48"W x 63"H (On Base)
Mokon, model Full Range 311708, combination heater and chiller. Temperature range of 35°F to 200°F depending on materials, application and machine configuration. Rated up to 40 GPM at 32 PSI. Equipped with a single zone 9kW heater, 5 HP compressor, ¾ hp chiller supply pump and 1½ HP process pump. Process, supply and drain fittins are 1" FNPT and has a ½" FNPT system drain with ball valve.
OAD: 60"L x 38"W x 48"H
Mokon, model Full Range 311708, combination heater and chiller. Temperature range of 35°F to 200°F depending on materials, application and machine configuration. Rated up to 40 GPM at 32 PSI. Equipped with a single zone 9kW heater, 5 HP compressor, ¾ hp chiller supply pump and 1½ HP process pump. Process, supply and drain fittins are 1" FNPT and has a ½" FNPT system drain with ball valve.
OAD: 60"L x 38"W x 48"H
Mokon, model Full Range 311708, combination heater and chiller. Temperature range of 35°F to 200°F depending on materials, application and machine configuration. Rated up to 40 GPM at 32 PSI. Equipped with a single zone 9kW heater, 5 HP compressor, ¾ hp chiller supply pump and 1½ HP process pump. Process, supply and drain fittins are 1" FNPT and has a ½" FNPT system drain with ball valve.
OAD: 60"L x 38"W x 48"H
Mokon, model Full Range 311708, combination heater and chiller. Temperature range of 35°F to 200°F depending on materials, application and machine configuration. Rated up to 40 GPM at 32 PSI. Equipped with a single zone 9kW heater, 5 HP compressor, ¾ hp chiller supply pump and 1½ HP process pump. Process, supply and drain fittins are 1" FNPT and has a ½" FNPT system drain with ball valve.
OAD: 60"L x 38"W x 48"H
Mokon, model Full Range 311708, combination heater and chiller. Temperature range of 35°F to 200°F depending on materials, application and machine configuration. Rated up to 40 GPM at 32 PSI. Equipped with a single zone 9kW heater, 5 HP compressor, ¾ hp chiller supply pump and 1½ HP process pump. Process, supply and drain fittins are 1" FNPT and has a ½" FNPT system drain with ball valve.
OAD: 60"L x 38"W x 48"H
Lee, Model 125LD12T, 125 liter (33 gallon) 316 stainless steel jacketed kettle. Vessel Dimensions: 25½" ID x 30" deep. Equipped with a tilt out bridge mounted triple motion agitator. Scrape and crossbar powered by a 5 Hp drive, high shear agitator powered by a 7½ hp drive, flush mounted sensor and 2" OD / 1½"ID tri-clamp style discharge with 15" ground clearance.
Top Fittings:
(1) 6" Tri-Clamp
(2) 3" Tri-Clamp
(3) 2" Tri-Clamp
(3) 1½" Tri-Clamp
Jacket Fittings: ¾" NPT
Nat’l Brd: 12861
MAWP: 150 PSI @ 366° F (jacket)
MDMT: -20°F @ 150 PSI (jacket)
MAWP: 50/FV PSI @ 300° F (vessel)
MDMT: -20°F @ 50/FV PSI (vessel)
OAD: 84"L x 50"W x 109"H
Bosch Model SVE 3800, automatic, stainless steel, vertical form fill and seal machine. Rated from 20 to 100 packages per minute – depending on materials, application and machine configuration. Package size range: 3.2" to 20" in Length; 3.2" to 14.2" in Width. Equipped with powered film unwind, film registration, 10" vertical lap seal, dual side belt film assist, 15½" wide seal jaws and mechanical bag gusset. Film specifications: up to 30" in Width; up to 15" in Diameter; 3" Core. Control panel with AB controller and touch screen HMI.
OAD: 96"L x 78"W x 78"H
Pasteurizing system with a 30 Gallon, stainless steel, tank and heat exchange system. Vessel dimensions: 25½" diameter with a 17" straight wall, dome top and slant bottom. Equipped with a 7½ HP Ampco centrifugal pump, APV plate heat exchange and 2"ID x 500" long holding tube. System mounted on a stainless steel frame. Control panel with AB controller, touch screen HMI and chart recorder.
OAD: 72"L x 48"W x 89"H – HTST Skid
72"L x 17"W x 67"H – Control Cabinet