Bliss Model E1906, Heavy duty, mild steel, dual screen, hammer mill, with 576 square inch screen area and up to 1740 rpm production rates – depending on materials and application. Equipped with a 13″ x 9-1/2″ OD, 9″ x 6″ ID top flanged product in feed with (8) 3/8″ bolt holes on 5-1/2″ centers, octagonal housing, 9″ OD recessed reversible rotor with (8) 6″ Long x 2″ Wide knife / blunt swing blades. Side access doors with one piece, spring loaded, quick change screen carriage, drive shaft locking device, adjustable non leak air sweep, saftey and vibration sensor switches, 10″ x 7-1/2″ OD, 7″ x 4-1/2″ ID side bottom flanged discharge port with (6) 3/8″ bolt holes on 4″ centers, and 9″ x 7″ OD air relief port, 10 hp drive, and a start/stop control package. Mounted on heavy duty base frame.
OAD: 48″ L x 29″ W x 44″ H
Blommer, 45,000 lbs, carbon steel, horizontal, low pressure, jacketed, chocolate melting and mixing vessel, with pounds of product per hour – depending on materails and application. Inner chamber dimension: 168″ in Length; 91″ in Width; 100″ in Depth. Equipped with covered top with a 24″ x 24″ manway, self contained heating and center bottom 2½”OD / 2″ID tri-clamp discharge with 15″ ground clearance.
Jacket:
(10) 2″ NPT
OAD: 216″L x 96″W x 130″H
Blommer, 45,000 lbs, carbon steel, horizontal, low pressure, jacketed, chocolate melting and mixing vessel, with pounds of product per hour – depending on materails and application. Inner chamber dimension: 168″ in Length; 91″ in Width; 100″ in Depth. Equipped with covered top with a 24″ x 24″ manway, self contained heating and center bottom 2½”OD / 2″ID tri-clamp discharge with 15″ ground clearance.
Jacket:
(10) 2″ NPT
OAD: 216″L x 96″W x 130″H
Miura, model LX-50SG-12, gas fired steam boiler. Rated up to 1,970,000 BTUH.
Horsepower: 50 BHP
Steam Output: 1,730 LB/HR
Maximum Pressure: 170 PSI
Operating Pressure Range: 70-150 PSI
Design Temp: 400°F
Fuel Type: Natural Gas
Gas Supply Pressure: 3-5 PSI
OAD: 97"L x 34"W x 102"H
Rietz Model RE24K7E333, Stainless steel extructor, designed for grinding frozen, partially frozen, or fully thawed 40 lb pound blocks of product rated from 40 to 30,000 lbs per hour – depending on materials and application. Equipped with 30″ long x 27″ wide x 34″ ID stainless steel crevice free product hopper with (6) 10″ long x 7″ high hammer blades on 8″ OD shaft and (6) 5″ long x 8 high stationary anvils (no knives / no sharpening, low maintenance), 24″ ID rotary product reduction port, with swing open, bolt down cover, reduction screen (change part per application) with 47″ floor clearance, chain to sprocket 30 Hp motor drive with safety guarding. Mounted on (4) leg base frame.
Reduction screen is change part per application.
OAD: 95″ L x 45″ W x 111″ H
Lehmann Model 5 roller mill used as a refiner for chocolate masses, creams, soaps, or inks, to ensure homogeneous product fineness with amount of product per hour – depending on materials and application Equipped (5) rollers 16" (400mm) OD and 43" Long with a working surface of 40" (1000mm) Wide and jacketed for heating and cooling. The refiner features a receiver and product bin measuring 39" Wide x 51" High with hydraulic roller height adjustments, and a control box with plow down / lift, an hour meter with E-stop. Unit allows independent control of the first roll rotation speed through a variable speed drive unit. The first roll is brought near the second roll, which remains fixed in position, by means of a hydraulic cylinder equipped with a precise positioning system. The centrifuged cast iron rolls have an extremely hard outer surface to allow for long life and limited wear.
Mounted on heavy duty frame.
OAD: 5′ L x 8′ W x 8′ H
Flexicon, Model 1450, Rated up to 140 ft³ of product per hour – depending on materials, application and product density. Equipped with 30” long x 30” wide x 24” deep stainless steel agitated product hopper and cover with ½ Hp agitator drive, and mounted on (4) legs, with 3" OD x 151" long stainless steel product conveying screw, 4" OD x 120" long flexible poly tube and has top mounted 3 Hp motor drive with 6” ID product discharge port Control panel has start, stop, e-stop controls. Mounted on stainless steel Model PB1-S-X Portable base with support mast and has (2) 6" swivel casters with brake under hopper and (2) 6" rigid casters with extended length base and Tilt-Down support mast with manually actuated hydraulic jack.
OAD: 152" L x 46" W x 132" H
Morcos, Model RM600, 21 ft³, (17 ft³ working capacity), double ribbon mixer with pounds of product per hour – depending on materials and application. 316L stainless steel contact parts. Inner mixing chamber dimensions of 60" in Length; 24" in Width; 26" in Depth. Equipped with flip up cover, lift out safety screens, 2¼" OD motor shaft, 1¾" wide x ¼" thick (outer) and 1¾" wide x (¼)" thick (inner) stainless steel ribbons. 11" OD center bottom discharge with 50" floor clearence and 7.38 Hp motor. Mounted on stainless steel (4) leg frame with 35" wide x 121" long stainless steel platform set 57" off the ground with 36" high rails and a 6-step staircase.
OAD: 125"L x 102"W x 103"H
BMI, stainless steel inclined conveyor. Equipped with a 13" infeed height, 18" wide conveyor belt. Conveyor has a 67" long incline with a 72" long top horizontal run and a 36" discharge height. Powered by a ½ hp motor drive with variable speed and mounted on a (4) leg stainless steel base frame.
OAD: 140"L x 34"W x 39"H
Bandrite Model 6000 RTL, Automatic, continuous motion, band style bag sealer rated from 250 to 750 inches per minute with number of bags – depending on materials, application and operator dexterity. Equipped with angled, tilt away sealing head has ¾" wide heat sealing and cooling bars with non-marking carrier belts, adjustable running speeds and temperature controls up to 600°F, bag trim station, 1 line coder and hand crank height adjustable for different size bags. Mounted over 6" wide x 100" long stainless steel conveyor with variable speed controller powered by ¼ Hp drive.
OAD: 108" L x 36" W x 59" H
Ishida, DACS-GN-S060-34, automatic, stainless steel checkweigher rated up to 300 feet per minute with number of product – depending on materials and application. Weight range: from 30 to 6000 grams. Accuracy to: +/- 1 grams depending on application with minimum graduation of 0.5 gram. Equipped with 17" long x 12½" wide infeed conveyor belt, with stainless steel guide rails, 17" long by 12½" wide weighing conveyor with load cell, and 29" long by 12½" wide discharge conveyor with dual mechanical reject arms. Touch pad operator interface with visual display. Mounted on a stainless steel frame with height adjustable legs.
OAD: 66" L x 32" W x 57" H
Kramer Grebe / Convenience Foods Systems, vacuum bowl chopper and mixer, for cutting, mixing and emulsifying product up to 325 liters per batch – depending on materials and application. All 304 stainless steel construction. Equipped with 70" OD x 40" high (to top of cover) mixing chamber, 9-1/2" top port, with hydraulic lift. Spiral cutting head is capable of using from 2 to 12 blades, currently set-up with 8 blades which can be positioned at angles of both 30 and 60 deg of each other and has hydraulic loading station for standard product carts. (carts not included). Two speed mixing bowl, and spiral knife motor drives, 28" Diameter hydraulic product un-loader with knife speed and portion controls. Mounted on heavy duty frame.
OAD: 130" L x 90" W x 76" H
