Arpac Machines

Arpac Shrink Bundler BPMP-5152

• Manufacturer: Arpac
• Model Number: BPMP-5152
• Frain Number: 5J2090

Arpac, Model BPMP-5152, Automatic, inline shrink bundler and tunnel. Rated 10 to 35 packages per minute – depending on materials and application. Product size range: 3" to 12" in Length; 6" to 18" in Width; 3" to 12" in Height. Equipped with 72" long x 20" wide infeed conveyor, laner to flight bar transfer system and 33" long x 26½" wide overlap wrap conveyor section. Dual side film racks with splicer, servo controlled film feed, dancer and tension rollers with exact print registration, has smooth wrapping motion and bottom overlap wrapped sleeve. Film up to 26" maximum in width; 20" in maximum OD with 3" OD core with film cut from supply roll and film type low density polyethylene.

Shrink tunnel has 22" wide x 13" high aperture, x 68" long heat shrink chamber and 102" long x 25" wide conveyor, heating zone with heat controls, air recirculation fans and (1) end discharge cooling fans. Control panel has A/B PLC controller, with touch pad controls, HMI and flight bar, cycle, power on, stop and e-stop push button controls with product jog, run and registration control switches, . Mounted on heavy duty frame with safety guarding and status light bar.

OAD: 384"L x 68"W x 105"H

Arpac Shrink Flow Thru TS37

• Manufacturer: Arpac
• Model Number: TS37
• Frain Number: R34640

Arpac Model TS37 / XT18, Horizontal, continuous motion, side seal shrink wrapper and tunnel rated from 0 to 90 linear feet or 0 to 80 packages per minute – depending on materials, application and product stability. Product size range: 3-1/2" to 60" in Length; 2" to 16" in Width; 1/4" to 7-1/2" in Height. Equipped with 120" long lugged product in feed conveyor, LDPE seal jaws with next generation side seal with film registration and product discharge conveyor. Film specs: up to 39" wide single wound film on 3" OD core; to 14" OD with pull out film carriage. Control panel has A/B controller, with no product detection, perf and scrap removal wheels, seal bar trim, tempature controllers, drive speed dial with start, stop, jog and e-stop. Mounted on (4) leg frame with interlock safety guarding.

Shrink tunnel: Aperture: 24" in Width; 14" in Height; tunnel 72" in Length. Equipped with 120" long x 22" wide product conveyor, top mounted blower with variable speed and temperature controls. Mounted on height adjustable (4) leg frame.

OAD: 251" L x 63" W x 61" H

Arpac Shrink Bundler BPMP5300

• Manufacturer: Arpac
• Model Number: BPMP5300
• Frain Number: 5J1231

Arpac, Model BPMP-5300, Automatic, continuous motion, servo driven, shrink bundler and tunnel with in feed conveyor and laner, has bottom overlap and rated from 10 – 60 packages per minute – depending on materials, application and machine configuration. Product size range: 3" to 12" in Length; 6" to 18" in Width; 3" to 12" in Height. Equipped with 302" long x 20½" wide plastic in feed conveyor with overhead servo laner to flight bar transfer with 32" long x 26½" wide overlap wrap conveyor section and 8" long x 20" wide discharge conveyor to shrink tunnel. Dual side film racks with splicer, servo controlled film feed with dancer and tension rollers and exact print registration, with smooth wrapping motion and bottom overlap wrapped sleeve . Film up to 26" maximum in width; 20" in maximum OD with 3" OD core with film cut from supply roll
Shrink tunnel has 22" wide x 13" high aperture, x 70" long heat shrink chamber and 105" long x 25" wide conveyor, heating zone with heat controls, air recirculation fans and (2) end discharge cooling fans. Control panel has A/B PLC controller, with touch pad controls, display, flight bar, cycle, power on, stop and e-stop push button controls with product jog, run and registration control switches, safety guarding and status light bar. Mounted on heavy duty frame.

OAD: 484"L x 87"W x 108"H

Arpac Shrink Bundler 737C

• Manufacturer: Arpac
• Model Number: 737C
• Frain Number: R34340

Arpac, semi automatic, inline, shrink bundler and tunnel. Rated from 1 to 15 bundles per minute – depending on materials, application and operator dexterity. Product size range: 6" to 18" in Length x 6" to 35" in Width x 6" to 18" in Height. Arpac Model 737C bundler equipped with 37" wide hot knife seal jaws with 20" vertical travel and (2) handed cycle start push buttons and roller transfer conveyor into shrink tunnel, powered film feed and has film specifications of 37" in width up to 14" in diameter on 3" OD core and film type polyethylene or low density polyethylene with film gauge of 1 to 3 mil.

Arpac Model HVP, single zone shrink tunnel with total aperture of 40” in width x 20" in height and has a chamber length of 60" with top mounted blower. Control panel has temperature, variable air flow, variable conveyor speed and e-stops. Capable of running boxes, trays, cartons or any conveyable type product. Mounted on a common frame with leveling legs.

OAD: 141" L x 61" W x 83" H

Arpac Shrink Bundler BPTW6000

• Manufacturer: Arpac
• Model Number: BPTW6000
• Frain Number: R36820

Arpac, Model BPTW-6000, Automatic, inline, continuous motion, registered film, shrink bundler and tunnel. Rated up to 60 bundles per minute – depending on materials and application. Product size range: 5" to 12" in Length; 6" to 20" in Width; 3" to 12 in Height. Film specs: to 26" in Width; to 20" in Diameter; on 3" core; can handle clear or printed film of 1.75 to 2.5 mil low density polyethylene and has maximum film cut-off length of 42". Equipped with dual side mounted film racks, splicing bar, infeed spacing conveyor, film registration, 28" seal bar and bottom overlap seal, (3) zone shrink tunnel with adjustable flow vents, variable speed blowers and cooling fans on discharge. Control panel has A/B controller with touch screen HMI and statis light bar. Mounted on heavy duty formed and structural steel frame with safety guarding.

OAD: 394"L x 104"W x 115"H

Arpac Case Packer Wrap Around PC2000

• Manufacturer: Arpac
• Model Number: PC2000
• Frain Number: R36685

Arpac Model PC2000, Automatic, intermittent motion, 5-axis servo driven, wrap-around case or tray packer rated 5 to 20 cases per minute with number of product – depending on materials and application. Case size range: 3.2" to 15.3" in Length x 7.7 to 23.2" in Width x 4.7" to 14.7" in Height with manufacturers joint inside or outside. Equipped with 26" wide x 96" long product in feed laner conveyor and has 20" wide x 50" long automatic blank case magazine, side recipacating pick and place, (4) chains adjustable with single load bar, servo drives and Nordson ProBlue hot melt glue system, flap closers and wrap over case station. Control panel has A/B PLC and on board A/B touch screen HMI controller, Seko gauges with e-stop. Mounted on heavy duty frame with interlock safety door guarding.
Capable of handling metal or paper cans, glass and plastic jars and bottles with proper change parts. Collates the product loads into a case or tray and seals them with hot-melt glue.

OAD: 215"L x 94"W x 106"H
40" L x 18" W x 80" H – Control Panel

Arpac Shrink Bundler 108-28RA

• Manufacturer: Arpac
• Model Number: 108-28RA
• Frain Number: R35410

Arpac, Model 108-28 RA, right angle shrink bundler. Rated from 10 to 20 bundles per minute – depending on materials, application and machine configuration. Equipped with 14" wide x 50" long in feed conveyor, 90° product pusher, 29" wide hot knife seal jaws with 13" vertical travel and bundle hold down tamp. 60" long single zone shrink tunnel has 26” wide x 18" high total aperture, 86" long x 29" wide product conveyor and cooling fan on discharge. Control panel with AB controller, touch screen HMI and digital temperature controls for seal bar and tunnel. Mounted on heavy duty base frame.

OAD: 189"L x 74"W x 85"H

Arpac Shrink Bundler 45TW28

• Manufacturer: Arpac
• Model Number: 45TW28
• Frain Number: R36810

Arpac, Model 45TW-28, inline, intermittent motion, bundler and integrated shrink tunnel.Equipped with 70" long x 24" wide in feed conveyor, 29" wide seal jaw with 12" vertical travel, side mounted film racks and splice station, 66" long x 17" wide transfer conveyor through seal and into single zone shrink tunnel with 29" wide flex link conveyor and 28” in width x 16" in height aperture and 70" long chamber, top mounted blower motor and cooling blower at discharge. Allen-Bradley controller with PanelView operator interface and color touch screen, message display and self-diagnostics, low film alert, bypass mode – allows product to pass through the machine without being wrapped and without heating the tunnel. Mounted on heavy duty frame with status light bar and interlocked safety guarding. Speed dependent on materials, application and machie configuration. Film rolls up to 28" in width; and 14" OD on 6" core.

OAD: 262"L x 80"W x 88"H

Arpac Shrink Bundler BPTW6000

• Manufacturer: Arpac
• Model Number: BPTW6000
• Frain Number: R36020

Arpac, Model BPTW-6000, Automatic, inline, continuous motion, registered film, shrink bundler and tunnel. Rated up to 60 bundles per minute – depending on materials and application. Product size range: 5" to 12" in Length; 6" to 20" in Width; 3" to 12 in Height. Film specs: to 26" in Width; to 20" in Diameter; on 3" core; can handle clear or printed film of 1.75 to 2.5 mil low density polyethylene and has maximum film cut-off length of 42". Equipped with dual side mounted film racks, splicing bar, infeed spacing conveyor, film registration, 28" seal bar and bottom overlap seal, (3) zone shrink tunnel with adjustable flow vents, variable speed blowers and cooling fans on discharge. Control panel has A/B controller with touch screen HMI and statis light bar. Mounted on heavy duty formed and structural steel frame with safety guarding.

OAD: 394"L x 104"W x 115"H

Arpac Shrink Tunnels VT122272

• Manufacturer: Arpac
• Model Number: VT122272
• Frain Number: R36682

Arpac VT122272, Inline shrink tunnel rated up to 100 feet per minute with number of product – depending on materials and application. Aperture: 12" in Height; 22" in Width. Tunnel: 72" in Length. Equipped with 92" long x 22" wide mesh conveyor belt, site glass viewing window, illuminated heating chamber, three top blowers, and variable speed / temperature controls. Mounted on height adjustable legs with casters.

OAD: 96" L x 35" W x 65" H

Arpac Shrink Flow Thru XRV15

• Manufacturer: Arpac
• Model Number: XRV15
• Frain Number: R36681

Arpac, Model XRV15, servo driven horizontal continuous motion shrink wrapper. Package size range: 3" to 11" in Length; 3" to 5" in Width; 1/8" to 12" in Height. Equipped with a 92" long lugged in feed conveyor set on 12" centers (48" load area), 25" wide pre folded side film unwind (utilizes center folded film), 6" long NextGen side seal mechanism, 12" wide vertical hot knife end seal and 6" wide by 60" long discharge conveyor. A/B PLC controller with touch screen HMI. Rated from to 90 linear feet per minute. Number of products per minute / hour dependent on material, application and machine configuration.
Arpac, Model XT18, Convection shrink tunnel. Equipped with 12" in Height; 21" in Width total aperture with 73" Long shrink heat chamber, 86" long x 17¼" wide composite conveyor, illuminated shrink chamber with viewing window. Swivel control panel with variable speed, temperature and air velocity controls. Mounted on casters and leveling legs. Number of products per minute / hour dependent on material, application and machine configuration.

OAD: 189"L x 73"W x 65"H Wrapper
OAD: 88"L x 45"W x 65"H Tunnel

Arpac Shrink Flow Thru AL18-B

• Manufacturer: Arpac
• Model Number: AL18-B
• Frain Number: R36680

Arpac, Model AL18-B, horizontal flow thru shrink wrapper. Rated from 0 to 100 linear feet per minute with number of product – depending on materials, application and machine configuration. Package size range: 3" to 34" in Length; ½" to 18" in Width; 1/8" to 8" in Height. Equipped with a 18" wide x 118" long slip torque in feed conveyor, 14-3/4" wide x 35" long transfer conveyor, 13-3/4" wide x 33" long discharge conveyor, 25" pre folded side film unwind, 6" long side seal and 20" wide hot knife end seal. Control panel has an A/B PLC controller and touch screen HMI.

OAD: 265"L x 68"W x 70"H