Hammer Machines

Used Hammer Equipment

Hammer mills use rotating hammer or knives to break-up wet or dry product that has been fed into the chamber of the machine. The rotating hammers or knives in the chamber of a hammer mill reduce the side of the product by impacting the product and by forcing the product to impact the interior of the chamber. The hammers within the chamber of a hammer are sized so that the end of the hammer almost impacts the interior wall of the chamber. A hammer mill has a screen to form the bottom of the chamber. Once the product has been reduced to the proper size, the product falls through the screen below the chamber. The screen can be changed to allow.

Hammer mills can be designed with different numbers of hammers or blades. The proper number of hammers or blades for an application is based the product that is to be processed, the size reduction necessary from the hammer mill, the volume that the hammer mill must process, and other specifications of the application. The hammers in a hammer mill can also have different features. The hammers can have knife edges, blunt (impact) edges, or a knife edge and a blunt edge. The type of hammer needed for the application is based on the type of product that is to be processed by the hammer mill. Hammer mills can also have fixed or swinging hammers or blades.

Contact Us

Hammer Equipment In Stock

Hosokawa Mill Hammer 3MP

  • Manufacturer: Hosokawa
  • Model Number: 3MP
  • Frain Number: 5H0301

Mikro Pulverizer, Model 3MP, hammer mill with carbon steel contact parts. Production rates per hour – depending on materials, application and machine configuration. Equipped with a 13" x 4" feed throat, (3) 2" diameter feed augers powered by a ¾ HP drive and (16) 13" wide swinging impact hammers powered by a 50 HP drive. Reduced product is collected in a 35" diameter x 32" deep conical hopper with a 12" diameter flanged discharge.

OAD: 70"L x 40"W x 64"H

Get a Free Quote Call: 630-629-9900

Micron Powder Systems Mill Hammer BANTAM

Micron Model Bantam, stainless steel hammer mill used to grind, chop, emulsify, de-lump, pulverize and process wet or dry product and capable of grinding down to 45 microns with proper change parts. Equipped with 7" OD x 7" deep product hopper with 7" long x 1" OD feed screw to grinding chamber with rotary swinging hammers, 12" OD cover with 5" OD air relief port and control panel with main machine and feeder start / stop buttons with amp gauge. Mounted on stainless steel frame with casters. Rates dependant on materials, application and machine configuration.

OAD: 36" L x 32" W x 44" H

Stainless Steel contact parts, 14000 max RPM speed and rotor driven by a 1HP (3/60/208-230/460V) motor . Single stainless steel screw feed, prewired stainless steel control station for main motor and screw feed motor. Portable.

Get a Free Quote Call: 630-629-9900

Micron Powder Systems Mill Hammer 2DH

Micron Model Mikro 2DH, hammer mill used to grind, chop, emulsify, de-lump, pulverize and process wet or dry product and capable of grinding down to 45 microns with proper change parts and rates of production per hour – depending on materials and application. Equipped with stainless steel contact parts, 16" wide x 16" long x 13" deep product hopper with 12" long x 3" OD twin feed screws to grinding chamber with (24) rotary split swing hammers driven by 15 Hp motor drive. 24" OD cover with 5" OD air relief port and control panel with main machine and feeder start / stop buttons, with amp gauge. Mounted on (4) leg painted base frame with casters.

OAD: 48" L x 48" W x 63" H

Get a Free Quote Call: 630-629-9900

Mikro Mill Hammer 25 HP

  • Manufacturer: Mikro
  • Model Number: 25 HP
  • Frain Number: 5H0302

Mikro Pulverizer, hammer mill with carbon steel contact parts. Production rates per hour – depending on materials, application and machine configuration. Equipped with a 13″ diameter x 6″ deep feed hopper, (3) 1¾” diameter feed augers powered by a ¾ HP drive and (12) 6″ wide swinging impact hammers powered by a 25 HP drive. Reduced product is discharge into a 24″ diameter x 15″ deep conical product hopper with a 10″ diameter flanged discharge.

OAD: 55″L x 55″W x 30″H

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer D6

  • Manufacturer: Fitzmill
  • Model Number: D6
  • Frain Number: 5A6702

Model D6 Comminuting (Hammer) Mill Has 16 Blunt Edge Swinging Hammer Blades. Mill Is Fed By 3" Auger Feed W/ 12" X 12" Feed Bin. Contact Parts On Feeder And Mill Are S/S Except Brass/Nickel Plated Chamber. Housing And Bearings Are Water Cooled. Three Shiv Selections And Belt Tension Adjust On Mill Drive For Speed Selection. Hammermill Mounted On Painted M/S Base With Discharge Height 6" Above Floor.

Overall Dimens: 41"L X 45"W X 32"H

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer DAS06 SS

  • Manufacturer: Fitzmill
  • Model Number: DAS06 SS
  • Frain Number: R18912

Stainless steel hammer mill used to grind,chop, emulsify, de-lump,pulverize and process wet and dry products. Equipped with a 29” x 20’" x 4” deep pan in feed, 16” long x 6” wide throat and fixed knife/impact blades. . Product discharge is 15”L x 5 1/2” W with 36” of clearance under the unit. Includers starter. Stainless steel base with locking casters.
OAD is 46”L x 30”W x 65”H

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer DASO6

  • Manufacturer: Fitzmill
  • Model Number: DASO6
  • Frain Number: 5G1520

Fitzmill Model DASO6, stainless steel hammer mill with production rates per hour – depending on materials and application. Equipped with start/stop controls, safety switch on cover, 14" long by 4-1/2" wide in feed, 11” long by 6” wide blade chamber and (16) 1" by 3-1/2" impact blades. Product discharge is 15” long x 5-1/2” wide with 22” floor clearance. Used to grind, chop, emulsify, de-lump, pulverize and process wet and dry products. Mounted on casters.

OAD: 53"L x 30"W x 59"H

Get a Free Quote Call: 630-629-9900

A C Horn & Co Mill Hammer CLSTRBST

  • Manufacturer: A C Horn & Co
  • Model Number: CLSTRBST
  • Frain Number: 5G2480

A.C. Horn, Model MTO-CLSTRBST-PW/A, stainless steel cluster buster. Equipped with a 57" wide x 63" long x 26" deep product hopper, (13) 35" diameter 4-blade fixed breakers powered by a 5 HP motor, 10" diameter x 60" long bottom auger with 9" centers powered by a 7½ HP motor, 10" x 10" discharge with 7" ground clearance. Unit mounted on stainless steel base.

OAD: 100"L x 70"W x 93"H

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer DAS0K12

  • Manufacturer: Fitzmill
  • Model Number: DAS0K12
  • Frain Number: 5G2953

Fitzmill Model DASOK12, 32 swing blade stainless steel comminutor mill with product volume per hour – depending on materials, application and machine configuration. Equipped with 20" wide x 22" long product hopper, 32 swing blade knives, 15" wide x 13"L discharge chute tapered down to 7"OD discharge with 27" discharge height. 20 Hp motor drive with Interlock safety guarding. Mounted on stainless steel base frame.

OAD: 52" x 40" x 65"

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer DAS06

  • Manufacturer: Fitzmill
  • Model Number: DAS06
  • Frain Number: 5G2710

Fitzmill Model DASO6, stainless steel hammer mill with production rates per hour – depending on materials and application. Equipped with 14" long by 4-1/2" wide in feed, 11” long by 6” wide blade chamber and (16) 1" by 3-1/2" impact blades. Product discharge is 15” long x 5-1/2” wide with 22” floor clearance, start / stop controls and safety switch on cover and mounted (4) leg base frame with casters. Used to grind, de-lump, pulverize and process wet / dry products.

OAD: 68" L x 32" W x 60" H

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer DKAS012

  • Manufacturer: Fitzmill
  • Model Number: DKAS012
  • Frain Number: 5F8860

Fitzmill, DKAS012, 316 Stainless steel vari-speed hammer mill. Equipped with with 32 stepped impact blades. Chamber dimensions: 13" long by 11" wide Discharge opening measures 17" by 13" with a floor clearance of 42". Mounted on stainless steel frame with casters.

Oad: 48" L x 36" W x 69" H

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer D6

  • Manufacturer: Fitzmill
  • Model Number: D6
  • Frain Number: 5F5113

Fitzmill Model D6 Hammer mill designed for various types of product reductions with volumes and speeds – depending on materials and application. Equipped with stainless steel bolt down safety cover, feed pan with 6" x 6" product feed port and 6" x 11" reduction throat, 16 fixed stainless steel knife and serrated impact blades, 6" Wide x 11" Long screen area, product discharge with 27” floor clearance, 5 hp belt motor drive with push botton start / stop controls and mounted on four leg frame with casters.

OAD: 46" L x 30" W x 52" H

Get a Free Quote Call: 630-629-9900
1 2 3 6