Hammer Machines

Used Hammer Equipment

Hammer mills use rotating hammer or knives to break-up wet or dry product that has been fed into the chamber of the machine. The rotating hammers or knives in the chamber of a hammer mill reduce the side of the product by impacting the product and by forcing the product to impact the interior of the chamber. The hammers within the chamber of a hammer are sized so that the end of the hammer almost impacts the interior wall of the chamber. A hammer mill has a screen to form the bottom of the chamber. Once the product has been reduced to the proper size, the product falls through the screen below the chamber. The screen can be changed to allow.

Hammer mills can be designed with different numbers of hammers or blades. The proper number of hammers or blades for an application is based the product that is to be processed, the size reduction necessary from the hammer mill, the volume that the hammer mill must process, and other specifications of the application. The hammers in a hammer mill can also have different features. The hammers can have knife edges, blunt (impact) edges, or a knife edge and a blunt edge. The type of hammer needed for the application is based on the type of product that is to be processed by the hammer mill. Hammer mills can also have fixed or swinging hammers or blades.

Contact Us

Hammer Equipment In Stock

Fitzpatrick Mill Hammer DKAS012

  • Manufacturer: Fitzpatrick
  • Model Number: DKAS012
  • Frain Number: 5H2891

Fitzmill, Model DKAS012, stainless steel hammer mill with pounds of product per hour – depending on materials and application. Equipped with a 2"OD / 1¼"ID seated bevel style charge port, (32) 3¼" long x 1½" wide fixed knife / impact blades and 3½"OD / 3"ID Tri-clamp style discharge with 26" of ground clearance. Mounted on (4) leg painted frame base.

OAD: 50"L x 45"W x 62"H

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer DAS06

  • Manufacturer: Fitzmill
  • Model Number: DAS06
  • Frain Number: 5H3878

Fitzmill, Model DASO6, stainless steel hammer mill with production rates per hour – depending on materials, application and machine configuration. Equipped with a 24" long x 20" wide x 4" deep feed pan, 6" wide x 4" high feed throat, 11” long x 6” wide blade chamber and (16) fixed knife/impact blades powered by a 7½ Hp motor drive. Product discharge is 15½” long x 5¾” wide with 36” floor clearance. Start / stop controls, mounted on (4) legs with casters.

OAD: 52"L x 30"W x 64"H

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer DAS06

  • Manufacturer: Fitzmill
  • Model Number: DAS06
  • Frain Number: 5G7400

Fitzmill, Model D, stainless steel hammer mill. Equipped with 12" long x 12" wide x 12" deep (½ ft³) product hopper, 3" diameter feed screw with 2" centers powered by ¼ HP drive with variable speed gearbox and (16) 3½" long x 1" wide fixed knife / impact blades. Product discharge is 15”L x 5½” W with 36" of ground clearance. Mounted on (4) leg mild steel frame with casters.

OAD: 55"L x 42" W x 64"H

Get a Free Quote Call: 630-629-9900

Carle Montanari Mill Hammer MAP400S

Carle Montanari, Model MAP 400S, compact, pin mill for grinding cocoa nibs to liquor with production rates per hour of 400 kgs or 880 lbs per hour – depending on materials and application. Equipped with 17" diameter radial flow disc’s, with staggered positioned pins and independent 15 Hp motor drives that rotate in opposite directions and self clean themselves as they rotate, with swing open, bold down access cover, 16" diameter x 15" long cone product hopper with 1Hp motor drive, 3" OD feed screw, bottom liquor collection valve. Mounted on (4) leg base frame.
Operation: Cocoa nibs are fed into grinder and crushed into small particles with cocoa liquor fluidity of 96.8% thru a 200 mess fineness screen.

OAD: 64" L x 46" W x 76" H

Get a Free Quote Call: 630-629-9900

Bliss Mill Hammer E1906

  • Manufacturer: Bliss
  • Model Number: E1906
  • Frain Number: 5E9992

Heavy duty, mild steel, dual screen, hammer mill, with 576 sq inch screen area and up to 1740 rpm, production rates – depending on materials and application. Equipped with a 13" x 9-1/2" OD, 9" x 6" ID top flanged product in feed with (8) 3/8" bolt holes on 5-1/2" centers, octagonal housing, 9" OD recessed reversible rotor with (8) 6" Long x 2" Wide knife / blunt swing blades. Side access doors with one piece, spring loaded, quick change screen carriage, drive shaft locking device, adjustable non leak air sweep, saftey and vibration sensor switches, 10" x 7-1/2" OD, 7" x 4-1/2" ID side bottom flanged discharge port with (6) 3/8" bolt holes on 4" centers, and 9" x 7" OD air relief port, 10 hp drive, and a start/stop control package. Mounted on heavy duty base frame.

OAD: 48" L x 29" W x 44" H

Get a Free Quote Call: 630-629-9900

Bliss Mill Hammer E1906

  • Manufacturer: Bliss
  • Model Number: E1906
  • Frain Number: 5E9990

Bliss Model E1906, Heavy duty, mild steel, dual screen, hammer mill, with 576 square inch screen area and up to 1740 rpm production rates – depending on materials and application. Equipped with a 13" x 9-1/2" OD, 9" x 6" ID top flanged product in feed with (8) 3/8" bolt holes on 5-1/2" centers, octagonal housing, 9" OD recessed reversible rotor with (8) 6" Long x 2" Wide knife / blunt swing blades. Side access doors with one piece, spring loaded, quick change screen carriage, drive shaft locking device, adjustable non leak air sweep, saftey and vibration sensor switches, 10" x 7-1/2" OD, 7" x 4-1/2" ID side bottom flanged discharge port with (6) 3/8" bolt holes on 4" centers, and 9" x 7" OD air relief port, 10 hp drive, and a start/stop control package. Mounted on heavy duty base frame.

OAD: 48" L x 29" W x 44" H

Get a Free Quote Call: 630-629-9900

Fluid Air Mill Hammer 003

  • Manufacturer: Fluid Air
  • Model Number: 003
  • Frain Number: 5C0057

Stainless steel Fluid Air comminuting / hammer mill rated up to 6,000 RPM. Equipped with feed auger, reversing blade feature, dual frequency drives.
Capable of handling both wet or dry products. Able to reduce to 40 microns. Results dependant on materials, application and machine configuration. Screens required per application. Mounted on casters.

OAD: 45"l x 25"w x 6’9"h

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer DAS06

  • Manufacturer: Fitzmill
  • Model Number: DAS06
  • Frain Number: R30620

Fitzmill, Model DASO6, stainless steel hammer mill. Equipped with a 12" L x 12" W x 12" D (½ ft³) product hopper, 4" diameter feed screw powered by a 1 HP drive with variable speed gearbox and (16) 4" L x 1" W swing impact blades powered by a 10 HP drive. Product discharge is 15”L x 5½” W with 45" of ground clearance.

OAD: 60"L x 55"W x 70"H

Get a Free Quote Call: 630-629-9900

Fitzpatrick Mill Hammer JT

  • Manufacturer: Fitzpatrick
  • Model Number: JT
  • Frain Number: R30360

Fitzpatrick, Model JT, 316 stainless steel homoloid mill. with production rates per minute – depending on materials and application. Equipped with 12" ID x 3" deep 304 stainless steel feed pan with 2.75" ID product port, (12) swinging knife / impact blades with screen area of 2" wide x 16" long and 8" long x 2" wide bottom product discharge with 35” ground clearance. Push button start /stop controls and mounted on a base with locking casters.

OAD: 35"L x 32"W x 55"H

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer DA0S6

  • Manufacturer: Fitzmill
  • Model Number: DA0S6
  • Frain Number: R30380

Fitzmill, Model DAS06, stainless steel hammer mill with pounds of product per hour – depending on materials and application. Equipped with 20" wide x 20" long x 4" deep feed pan, (16) fixed knife / impact blades and 15" x 5" discharge with 32" of ground clearance. Mounted on (4) leg stainless steel frame with casters.

OAD: 48"L x 30"W x 61"H

Get a Free Quote Call: 630-629-9900

Fitzmill Mill Hammer DKAS012

  • Manufacturer: Fitzmill
  • Model Number: DKAS012
  • Frain Number: R30383

Fitzmill, Model DKAS012, stainless steel hammer mill with pounds of product per hour – depending on materials and application. Equipped with 20" wide x 24" long x 4" deep feed pan, (32) 3" long x 1½" wide fixed knife blades and 12" x 15" discharge with 45" of ground clearance. Mounted on (4) leg stainless steel frame with casters

OAD: 50"L x 50"W x 78"H

Get a Free Quote Call: 630-629-9900

Fitzpatrick Mill Hammer DASO6

  • Manufacturer: Fitzpatrick
  • Model Number: DASO6
  • Frain Number: R29590

Fitzmill, Model DASO6, stainless steel hammer mill with production rates per hour – depending on materials, application and machine configuration. Equipped with a 28" long x 20" wide x 4" deep feed pan, 6" wide x 4" high feed throat, 11” long x 6” wide blade chamber and (16) fixed knife/impact blades powered by a 7½ Hp motor drive. Product discharge is 15½” long x 5¾” wide with 34” floor clearance. Start / stop controls, mounted on (4) legs with casters.

OAD: 48"L x 35"W x 64"H

Get a Free Quote Call: 630-629-9900